linesbion.blogg.se

Edgerouter x vpn
Edgerouter x vpn













edgerouter x vpn
  1. #EDGEROUTER X VPN HOW TO#
  2. #EDGEROUTER X VPN DOWNLOAD#

Set firewall modify balance rule 30 modify table mainĪt this point, this step will add Firewall rules, to exclude the private networks we define in the step 2 and the IP address belonging to the WAN interfaces (eth0 and eth1 in our example). Set firewall modify balance rule 30 destination group address-group ADDRv4_eth1 Set firewall modify balance rule 30 action modify Set firewall modify balance rule 20 modify table main Set firewall modify balance rule 20 destination group address-group ADDRv4_eth0 Set firewall modify balance rule 20 action modify Set firewall modify balance rule 10 modify table main Set firewall modify balance rule 10 destination group network-group PRIVATE_NETS set firewall modify balance rule 10 action modify Create a firewall modify policy with exclusion rules for the WAN interface addresses and the network group created earlier. On the step above, you can create all the RFC1918 network IP ranges or just the network segment corresponding to your internal network. Set firewall group network-group PRIVATE_NETS network 10.0.0.0/8 Set firewall group network-group PRIVATE_NETS network 172.16.0.0/12

#EDGEROUTER X VPN DOWNLOAD#

To take a backup, on the GUI you need to go to the “System” menu, go to the “Configuration Management & Device Maintenance” section and then click on the Download button under the Back-up Config section.Īfter taking a backup, you can proceed with the configuration following the steps below: Enter configuration mode configure Create a firewall network group specifying the private IP address ranges set firewall group network-group PRIVATE_NETS network 192.168.0.0/16 We storngly recommend to take a backup from the current configuration, should you need to rollback the changes. Now, after accesing the device through the CLI you can proceed with the configuration. You can do this using the CLI button in the GUI or by using a program such as PuTTY. In order to proceed with the configuration, you need to gain CLI access to the device. ISP Load Balancing Configuration using the CLI So, although there is a WAN Load balancing Wizard accessible through the GUI, we strongly recommend to perform this configuration using the CLI. It seems it is also a common issue that the GUI and the actual configuration go out of sync. I would say, the only disadvantage I see with the EdgeRouter from Ubiquiti is the GUI, there are several bugs or stuff that you cannot really do with the GUI. There are two ways of implementing WAN Load balancing on the router, one is using the GUI and other is using the CLI. The best thing is the cost of this device, it can be purchased at Amazon from around 95 dollars.

edgerouter x vpn

It includes several features like Routing, Firewall, NAT, VPN and ISP Load Balancing. The Operating System (EdgeOS) is a fork from Vyatta. If you don’t know about this device, I strongly recommend it to check it out, it is a low cost but powerful Router from Ubiquiti, ideal for small offices or as a home router.

#EDGEROUTER X VPN HOW TO#

I tried (not shown in config) to port fwd 54321 to wg0 without success.On this post we will describe, how to implement ISP Load Balancing with Ubiquiti EdgeRouter X. I feel like I have something wrong with ports on my router. wg show on the AWS server shows not much packets sent/received and router's show increasing Tx packets, no Rx. One odd thing is wg0 Tx spikes to ~80Mbps when I turn both routes on but nothing for Rx. Disabling the 2 routes brings back traffic instantly. Switching the 2 routes to enabled will drop all internet traffic but LAN devices stay accessible. On one end the EdgeRouter, on the other a Wireguard Server on AWS EC2.īasic routing plan is/was (worked with OpenVPN): I'm trying to accomplish something super easy with OpenVPN on my EdgeRouter X that seems impossible with WireGuard for me: Routing all traffic from LAN over the VPN interface and through to the internet.īoth ends connect fine using wg show showing handshakes and all. So I've read and tried all I could find on the interwebs and I stil can't get my head around this.















Edgerouter x vpn